Schedule Now!

 

 

Just how do you feel about How to Install a Bathtub?

Mounting a tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is additionally a reasonably challenging project. If the old bathtub is easily available, the project can relocate immediately; if you have to open a wall surface to eliminate the old bathtub as well as position the brand-new bath tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old bathtub and set in the new one. Make sure you have qualified yourself for the job and are comfortable trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is better to consider employing one before you begin. Possibilities are you may need an expert plumber to make tube links.
This post will certainly assist you set up a new tub in your shower room if you have already bought a brand-new tub and also don't need to alter the setup of your previous water supply pipes.
Your tools as well as product list should comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you must do is separate the water supply. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited accessibility that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a towel ready for the staying water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.

 

 

Fitting New Taps

If the tails of the new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washers are in location between the faucet as well as the sink. Protect the faucet in position with the maker supplied backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be linked to the faucet ends first, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Installing the Bathtub

Making use of both wood boards under its feet, put the tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little points.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by checking the level and also changing the feet on the bathtub till the spirit level reads degree.
To set up taps, fit all-time low of the furthest adaptable faucet connector to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the water supply and also check all joints and also new pipework for leaks and also tighten them if required. Load the tub and likewise check the overflow electrical outlet and the regular outlet for leakages.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling as well as sealing around the bath tub ought to wait till the bathtub has actually been used at the very least once as this will certainly settle it right into its last setting.

 

 

Planning for the Installation

To start with, the supporting structure supplied with the bathroom should be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the versatile tap ports to the bottom of both faucets utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its last setting.

 

 

Tiling Around the Bath tub

In the area where the bath fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, causing the water to permeate the wall surface in between the bath and the tiling, causing issues with wetness and also possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to permit the activity experienced when the tub is in use. The sealant can crack fairly early if you do not consider this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water-proof sticky and also cement.

 

Bathtub Installation

 

How Important Is A Bathtub To Your Home?

 

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

 

Install Piping Before Tub

 

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

 

Position the Tub

 

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

 

Assemble Drain Connections

 

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

 

Place a Pipe For the Shower Head

 

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

 

Attaching Hot and Cold Water Lines

 

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

 

Install the Spout

 

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

 

Check For Leaks

 

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

 

estore the Bathroom Wall

 

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

 

I found that blog post on How to Install a Bathtub Yourself when doing a lookup on the web. Please take the opportunity to share this article if you appreciated it. Many thanks for your time invested reading it.

Contact Us Today